長臂挖掘機

省時 省力 省財富

Before starting the construction of the crushing hammer, it should be thoroughly inspected. Firstly, check if the high and low pressure hoses of the crushing hammer are loose and check for any oil leakage. In order to improve the accuracy of hammering, it is necessary to ensure that the excavator is placed smoothly and reduce the possibility of shaking.

在使用破碎錘時，避免將錘壓得過實，同時也不能打空錘。正確的做法是將錘釺對準石塊後壓進內套裏，然後將其壓緊即可。切勿把履帶都抬起來，這樣會導致石塊打開後錘釺猛然下紮，對設備造成損害。在打擊石塊時，建議提前考慮下一個目標，並找好下錘麵，以保證作業順利進行。

When using a crushing hammer, avoid pressing the hammer too tightly and also avoid hitting the hammer empty. The correct approach is to align the hammer with the stone and press it into the inner sleeve, then press it tightly. Do not lift all the tracks, as this may cause the hammer to suddenly descend after the stone is opened, causing damage to the equipment. When striking stones, it is recommended to consider the next target in advance and find the next hammer surface to ensure smooth operation.

根據不同情況，調節破碎錘的打擊頻率是很重要的。對於小石頭塊和水泥塊等，可以將頻率調快，而對於大塊石頭或者死料，則適當調慢頻率，以提高作業效率。在破碎塊時，可以讓錘往前稍稍紮一點大錘，這樣大部分石塊會飛向前方，保護車輛玻璃和漆麵的。

It is important to adjust the strike frequency of the crushing hammer according to different situations. For small stones and cement blocks, the frequency can be increased, while for large stones or dead materials, the frequency can be appropriately reduced to improve work efficiency. When breaking the block, you can make the hammer strike slightly forward with the sledge hammer, so that most of the stones will fly forward, protecting the safety of the vehicle's glass and paint surface.

在打水泥和死山根時，不要一味往下打錘釺，這樣容易折斷錘釺。應該在錘釺打入山裏的一半時停止打錘，清理打下來的浮料，再繼續作業。定期檢查破碎係統的壓力、流量和氮氣是否充足，更好在大臂軸銷後邊或旋轉泵邊上加裝破碎錘回油過濾器，減少液壓油進、回油的汙染。

When drilling cement and dead roots, do not blindly hit the hammer and drill rod downwards, as this can easily break the hammer and drill rod. The hammer should be stopped halfway into the mountain, and the floating material should be cleaned before continuing the operation. Regularly check whether the pressure, flow rate, and nitrogen of the crushing system are sufficient. It is best to install a crushing hammer return oil filter on the back of the boom shaft pin or the rotating pump to reduce the pollution of hydraulic oil inlet and outlet.

破碎錘 的正確使用和保養對於保障設備穩定運行關重要。作為在惡劣工作條件下工作的設備，定期維護可以降低故障風險，延長設備使用壽命。除了及時對主機進行保養外，還應注意以下幾點：

The correct use and maintenance of the crushing hammer is crucial for ensuring the stable operation of the equipment. As equipment that operates under harsh working conditions, regular maintenance can reduce the risk of malfunctions and extend the service life of the equipment. In addition to timely maintenance of the host, the following points should also be noted:

1. 檢查有關螺栓是否鬆動，各連接銷軸是否過度磨損，並檢查釺杆與襯套之間的間隙是否正常，是否有油液滲出。若低壓油封已損壞，務必人員進行更換。

1. Check whether the bolts are loose, whether the connecting pins are excessively worn, and whether the gap between the drill rod and the bushing is normal, and whether there is oil leakage. If the low-pressure oil seal is damaged, it must be replaced by professional personnel.

2. 對工作裝置的潤滑點，在作業前及每次連續作業2～3小時後，應進行潤滑。

2. The lubrication points of the working device should be lubricated before and after 2-3 hours of continuous operation.

3. 對液壓油質進行定期檢查，工作環境不同，油液狀況可能有差異。觀察油質顏色來判斷其好壞，若油液嚴重變質，應及時更換並清洗油箱和濾油器。

3. Regularly inspect the hydraulic oil quality, and the oil condition may vary depending on the working environment. Observe the color of the oil to determine its quality. If the oil deteriorates severely, the oil tank and filter should be replaced and cleaned in a timely manner.

以上就加長臂挖掘機廠家為大家介紹的內容，感謝您在百忙之中查看我公司的信息內容http://www.neuesausbunutan.com，如果您想要了解的更多，歡迎您來電進行谘詢!

The above is the content introduced by the manufacturer of the extended arm excavator. Thank you for taking the time to check our company's information http://www.neuesausbunutan.com If you want to learn more, welcome to call for consultation!