長臂挖掘機

省時 省力 省財富

嚴格按照操作規程和駕駛要領，盡量避免換檔“齒”，以減少齒輪副的磨損。

Strictly follow the operating procedures and driving essentials, and try to avoid shifting gears as much as possible to reduce wear on the gear pair.

嚴格執行維護製度，加強換擋裝置的維護。當換擋裝置連接不當時，應及時調整，以保證換擋裝置的良好性能。

Strictly implement maintenance regulations and strengthen the maintenance of gear shifting devices. When the shifting device is not connected properly, it should be adjusted in a timely manner to ensure the good performance of the shifting device.

注意自鎖機構的修理和維護，及時修理或更換定位功能降低或失去定位效率的定位鋼球、彈簧和撥叉軸，使自鎖機構的自鎖性能處於良好狀態。

Pay attention to the repair and maintenance of the self-locking mechanism, and promptly repair or replace the positioning steel balls, springs, and shift forks that have reduced or lost positioning efficiency, so as to ensure that the self-locking performance of the self-locking mechanism is in good condition.

組裝變速器時，應嚴格遵守操作程序，以確保變速器的所有零件都得到正確調整和適當擰緊。在大型下坡道路上，駕駛員應嚴格遵循下坡運動的要點，不得違反規定。

When assembling the transmission, the operating procedures should be strictly followed to ensure that all parts of the transmission are correctly adjusted and properly tightened. On large downhill roads, drivers should strictly follow the key points of downhill movement and not violate regulations.

長臂挖掘機在行駛過程中，如果變速器出現“跳車停車”現象，應及時停機，然後才能查找原因，排除故障。具體方法是

During the operation of a long arm excavator, if the gearbox experiences a "jump stop" phenomenon, it should be stopped in a timely manner before the cause can be identified and the fault can be eliminated. The specific method is

在平坦路麵上行駛時，有“行程停車”，可按正常停車要領停車，並認真查找原因，排除故障。

When driving on flat roads, if there is a "travel stop", you can park according to normal parking instructions, carefully investigate the cause, and troubleshoot the problem.

下坡行駛時如果出現“跳車停車”，應根據加檔動作要領將檔位定位在高速位置或采取“抓檔”措施，行駛到坡底後停車檢查排除故障；如果“加檔”或“抓檔”不成功或“急停”再次出現，司機可將發動機轉速控製在中速，用“刹車”的方法使機器滑到坡底，然後排除故障。

If there is a "jumping stop" when driving downhill, the gear should be positioned at the high speed position or "grabbing gear" measures should be taken according to the essentials of the upshifting action. After driving to the bottom of the slope, stop and check to eliminate the fault; If "upshifting" or "grabbing" is unsuccessful or "emergency stop" occurs again, the driver can control the engine speed at medium speed, use "braking" to slide the machine to the bottom of the slope, and then troubleshoot.

上坡行駛時，出現“行程停止”，檔位可位於低速檔或ⅰ檔。當機器行駛到坡頂時，停止機器並排除故障；如果減速不成功或再次出現“急停”，根據坡道停車的要點和要求停車，然後排除故障。

When driving uphill, a "travel stop" occurs, and the gear can be in low speed or first gear. When the machine reaches the top of the slope, stop the machine and troubleshoot; If the deceleration is unsuccessful or an emergency stop occurs again, stop according to the key points and requirements of parking on a slope, and then troubleshoot.

本文由長臂挖掘機提供技術支持，更多的詳細精彩內容請點擊我們的網站 http://www.neuesausbunutan.com我們將會全心全意為您提供滿意的服務。

This article is supported by a long arm excavator. For more detailed and exciting content, please click on our website http://www.neuesausbunutan.com We will wholeheartedly provide you with satisfactory service.